Schmid Watson Przewodnik Instalacji Strona 63
- Strona / 129
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
LTU/NTU SZ-DOC-W5-1.pd
f
Operating Manual
V
ersion: 1.5
Revision: 2002-09-10 54
SEG-B: Segment defect alarm indication if regenerators present on channel B
LOOPREG: Regenerator loopback active
BERT: BER test activated
CLD-A Current limit detection on channel A
CLD-B Current limit detection on channel B
PID Display a pair mismatch when operating in 4p mode (master only)
7.3.3.4 ALARM H Command
A.) Alarm H command without time adjustment.
The ALARM H command displays alarm events of the past with a time stamp based on the
internal system time of the LTU. The time stamp shows the number of days elapsed and the
system time in format 24-hour:minute at the occurrence instant of the event.
This relative LTU system time is set to zero by each RESET command or power-on.
LTU_10_FMM> ALARM H
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Alarm History (day:hour:min)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+0:00:00 LOS-S alarm on
+0:00:00 remote alarm on
+0:00:02 LOS-S alarm off
+0:00:02 remote alarm off
~~~~~~~~~~~~~~~~~~~~~~~End of Alarm History~~~~~~~~~~~~~~~~~~~~~~~
LTU_10_FMM>
B.) Alarm H command with time adjustment.
Additional entering of the actual time in format 24-hour:minute when calling the ALARM H
command will modify the displayed time stamp to real time representation.
On basis of the time declaration entered by the user and the LTU's internal system time, the
event is marked with the number of days elapsed and the real time of the occurrence instant
in format 24-hour:minute
LTU_10_FMM> ALARM H 14:23
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Alarm History (day:hour:min)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+0:14:18 LOS-S alarm on
+0:14:18 remote alarm on
+0:14:20 LOS-S alarm off
+0:14:20 remote alarm off
~~~~~~~~~~~~~~~~~~~~~~~End of Alarm History~~~~~~~~~~~~~~~~~~~~~~~
LTU_10_FMM>
- WATSON 5 1
- Version Control 2
- LTU/NTU SZ-DOC-W5-1.pdf 3
- Operating Manual 3
- Revision: 2002-09-10 iv 3
- Contents 5
- Revision: 2002-09-10 viii 7
- 1 The Watson 5 Family 10
- 1.1 Important Safeguards 11
- 3 Revision: 2002-09-10 12
- 1.2 Ordering Information 13
- 1.2.3 Accessories 14
- 2 Installation Guide 16
- 2.3 Installing a Watson Modem 17
- 3.1.1 Master / Slave 18
- 3.1.2 Line Rate 19
- 3.1.3 Power Back-off 20
- 3.2.1 Framing 20
- 3.2.2 AIS Generation 21
- 3.2.3 AIS Detection 21
- 3.2.4 E1 Clock Modes 21
- Figure 3-1: Clock Sources 22
- 3.3 ISDN PRA Interface 23
- 3.3.1 PRA Mode 24
- 3.3.2 CRC4 Processing Options 24
- Digital Link 25
- TV3' 25
- 17 Revision: 2002-09-10 26
- 3.4 nx64 kbit/s Interface 29
- 3.4.5 Handshake Operation 30
- 3.4.6 Supported V.54 Loops 30
- 3.4.8 Clock Polarity 31
- 3.4.9 Byte Timing 31
- 3.5 Time Slot Mapping 32
- 25 Revision: 2002-09-10 34
- 3.6.1 TIA/EIA-485 4-wire Bus 35
- 3.6.2 TIA/EIA-485 2-wire Bus 36
- 4 Performance Monitoring 40
- 4.2.2 E1 Interface 41
- 4.2.3 ISDN PRA Interface 42
- 5.1 LEDs 44
- 5.1.2 Alarm Conditions 45
- 5.2 Alarm Relays 46
- 5.2.2 NTU 47
- 6 Power Concept 48
- 6.3 Remote Powering 49
- 41 Revision: 2002-09-10 50
- 7 Monitor 51
- 43 Revision: 2002-09-10 52
- 7.2.2 LTU Minirack 53
- 7.2.3 NTU 53
- 7.3.2.1 G826 Command 55
- 7.3.2.2 RESETG826 Command 57
- 7.3.2.3 STARTBER Command 57
- 7.3.2.4 STOPBER Command 58
- 7.3.2.5 READBER Command 58
- 7.3.2.6 RESETBER Command 59
- 7.3.3.1 DIAGNOSTIC Command 59
- 7.3.3.2 STATUS Command 60
- 7.3.3.3 ALARM Command 62
- 7.3.3.4 ALARM H Command 63
- 7.3.3.5 CLEAR Command 64
- 7.3.3.6 ACO Command 64
- 7.3.3.7 LOOP1 Command 65
- 7.3.3.8 LOOP2 Command 65
- 7.3.3.9 LOOPREGn Command 65
- 7.3.3.10 STARTAL Command 66
- 7.3.3.11 STOPAL Command 66
- 7.3.3.12 TRACETIME Command 66
- 7.3.3.13 RESET Command 66
- 7.3.3.14 RESETCARD Command 67
- 7.3.4.1 CONFIG Command 68
- 61 Revision: 2002-09-10 70
- 7.3.4.3 MP Command 71
- 63 Revision: 2002-09-10 72
- 7.3.4.4 TS Command 73
- 7.3.4.5 MODE Command 74
- 7.3.4.6 DEFAULT Command 75
- 7.3.6.2 RHM Command 77
- 7.3.6.3 RCHM Command 77
- 7.4.1.1 ALARM Command 78
- User interface in X.21 mode 79
- 7.4.2.1 CONFIG Command 80
- 7.4.2.9 UIF Command 82
- 7.4.2.10 DEFAULT Command 82
- 7.5.1 ADDRESS Command 85
- 7.5.2 V.11 WIRES Command 86
- 8.1 Features 88
- 8.2 Configuration 89
- 8.2.3 DSL Time Slot Selection 90
- Multipoint Configuration 91
- 8.2.4 MP Command 92
- 8.3 LEDs 96
- 9.1 Tabletop NTU, Rear Panel 98
- 9.2 Plug-in LTU, Front Panel 99
- 10 Connectors’ Description 100
- 10.2 E1 Connector 101
- 10.2.2 Impedance 75Ω 102
- 10.3 nx64 kbit/s Connector 103
- SZ-DOC-W5-1.pdf LTU/NTU 104
- Version: 1.5 Operating Manual 104
- 95 Revision: 2002-09-10 104
- 10.3.2 nx64 kbit/s Cables 105
- 10.3.2.2 V.35 DCE Cable 106
- 10.3.2.4 V.36 DCE Cable 108
- 10.3.2.6 X.21 DCE Cable 110
- 10.4 Monitor Connector (NTU) 111
- 10.5 48V 112
- Power Connector (NTU) 112
- 11 Technical Specifications 114
- 11.1.3 Monitor Interface 115
- 11.2 Power Supply 116
- 11.3 Environment 116
- 11.4 Physical Dimensions 117
- 12 Firmware Download 118
- Download via ACU 119
- Download via CMU 120
- Download via Modem Chain 121
- 113 Revision: 2002-09-10 122
- 13.1 Test Loops 123
- 13.2.1 Problems 124
- 13.2.2 Initialization Errors 125
- 14 Appendix 126
- 14.2 Referenced Documents 128
Powiązane produkty i podręczniki dla Networking Schmid Watson
Networking Schmid Watson Dokumentacja
(130 strony)
(130 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.733 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji