Schmid Watson Przewodnik Instalacji Strona 123
- Strona / 129
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
LTU/NTU SZ-DOC-W5-1.pd
f
Operating Manual
V
ersion: 1.5
Revision: 2002-09-10 114
13 Diagnostics and Troubleshooting
13.1 Test Loops
Standard Test Loops
The test loops can be activated via the monitor interface for both the master and the slave side.
However, only one test loop can be activated at any one time. Activation of a further test loop will
deactivate the previous loop. A system reset will deactivate any pending test loop.
MasterSlave
HDSL
Loop 1 Loop 2
Loop 1
TX
TXRX
RX
User
Interface
User
Interface
Figure 13-1: Standard Test Loops
Notes:
On the slave side, Loop 1 can only be activated locally, while Loop 2 can only be activated
remotely by the master.
Both the “Status Local” LED on the slave and the “Status Remote” LED on the master will be lit
amber when a loopback is active.
On the master side, Loop 1 can only be activated locally. Activating Loop 2 turns on Loop 2 at the
slave station. The “Status Local” LED will be lit amber when Loop 1 is active.
Analog Loopback
To test the DSL UNIT itself, the Analog Loopback can be used. To perform this test, the DSL
cable has to be disconnected from the unit, which must be configured as master. After that the
test can be activated with the appropriate monitor command (see chapter “Monitor”).
With actived Analog Loopback, the DSL transceiver receives the signal of its own transmitter due
to the impedance mismatch in the DSL line transformer. All data of the user interface is looped
back according to the interface settings.
No other test loop can be activated during Analog Loopback. STOPAL command, system reset or
power-up deactivating the Analog Loopback..
If activated, the Analog Loopback sets non-urgent alarms in status off.
- WATSON 5 1
- Version Control 2
- LTU/NTU SZ-DOC-W5-1.pdf 3
- Operating Manual 3
- Revision: 2002-09-10 iv 3
- Contents 5
- Revision: 2002-09-10 viii 7
- 1 The Watson 5 Family 10
- 1.1 Important Safeguards 11
- 3 Revision: 2002-09-10 12
- 1.2 Ordering Information 13
- 1.2.3 Accessories 14
- 2 Installation Guide 16
- 2.3 Installing a Watson Modem 17
- 3.1.1 Master / Slave 18
- 3.1.2 Line Rate 19
- 3.1.3 Power Back-off 20
- 3.2.1 Framing 20
- 3.2.2 AIS Generation 21
- 3.2.3 AIS Detection 21
- 3.2.4 E1 Clock Modes 21
- Figure 3-1: Clock Sources 22
- 3.3 ISDN PRA Interface 23
- 3.3.1 PRA Mode 24
- 3.3.2 CRC4 Processing Options 24
- Digital Link 25
- TV3' 25
- 17 Revision: 2002-09-10 26
- 3.4 nx64 kbit/s Interface 29
- 3.4.5 Handshake Operation 30
- 3.4.6 Supported V.54 Loops 30
- 3.4.8 Clock Polarity 31
- 3.4.9 Byte Timing 31
- 3.5 Time Slot Mapping 32
- 25 Revision: 2002-09-10 34
- 3.6.1 TIA/EIA-485 4-wire Bus 35
- 3.6.2 TIA/EIA-485 2-wire Bus 36
- 4 Performance Monitoring 40
- 4.2.2 E1 Interface 41
- 4.2.3 ISDN PRA Interface 42
- 5.1 LEDs 44
- 5.1.2 Alarm Conditions 45
- 5.2 Alarm Relays 46
- 5.2.2 NTU 47
- 6 Power Concept 48
- 6.3 Remote Powering 49
- 41 Revision: 2002-09-10 50
- 7 Monitor 51
- 43 Revision: 2002-09-10 52
- 7.2.2 LTU Minirack 53
- 7.2.3 NTU 53
- 7.3.2.1 G826 Command 55
- 7.3.2.2 RESETG826 Command 57
- 7.3.2.3 STARTBER Command 57
- 7.3.2.4 STOPBER Command 58
- 7.3.2.5 READBER Command 58
- 7.3.2.6 RESETBER Command 59
- 7.3.3.1 DIAGNOSTIC Command 59
- 7.3.3.2 STATUS Command 60
- 7.3.3.3 ALARM Command 62
- 7.3.3.4 ALARM H Command 63
- 7.3.3.5 CLEAR Command 64
- 7.3.3.6 ACO Command 64
- 7.3.3.7 LOOP1 Command 65
- 7.3.3.8 LOOP2 Command 65
- 7.3.3.9 LOOPREGn Command 65
- 7.3.3.10 STARTAL Command 66
- 7.3.3.11 STOPAL Command 66
- 7.3.3.12 TRACETIME Command 66
- 7.3.3.13 RESET Command 66
- 7.3.3.14 RESETCARD Command 67
- 7.3.4.1 CONFIG Command 68
- 61 Revision: 2002-09-10 70
- 7.3.4.3 MP Command 71
- 63 Revision: 2002-09-10 72
- 7.3.4.4 TS Command 73
- 7.3.4.5 MODE Command 74
- 7.3.4.6 DEFAULT Command 75
- 7.3.6.2 RHM Command 77
- 7.3.6.3 RCHM Command 77
- 7.4.1.1 ALARM Command 78
- User interface in X.21 mode 79
- 7.4.2.1 CONFIG Command 80
- 7.4.2.9 UIF Command 82
- 7.4.2.10 DEFAULT Command 82
- 7.5.1 ADDRESS Command 85
- 7.5.2 V.11 WIRES Command 86
- 8.1 Features 88
- 8.2 Configuration 89
- 8.2.3 DSL Time Slot Selection 90
- Multipoint Configuration 91
- 8.2.4 MP Command 92
- 8.3 LEDs 96
- 9.1 Tabletop NTU, Rear Panel 98
- 9.2 Plug-in LTU, Front Panel 99
- 10 Connectors’ Description 100
- 10.2 E1 Connector 101
- 10.2.2 Impedance 75Ω 102
- 10.3 nx64 kbit/s Connector 103
- SZ-DOC-W5-1.pdf LTU/NTU 104
- Version: 1.5 Operating Manual 104
- 95 Revision: 2002-09-10 104
- 10.3.2 nx64 kbit/s Cables 105
- 10.3.2.2 V.35 DCE Cable 106
- 10.3.2.4 V.36 DCE Cable 108
- 10.3.2.6 X.21 DCE Cable 110
- 10.4 Monitor Connector (NTU) 111
- 10.5 48V 112
- Power Connector (NTU) 112
- 11 Technical Specifications 114
- 11.1.3 Monitor Interface 115
- 11.2 Power Supply 116
- 11.3 Environment 116
- 11.4 Physical Dimensions 117
- 12 Firmware Download 118
- Download via ACU 119
- Download via CMU 120
- Download via Modem Chain 121
- 113 Revision: 2002-09-10 122
- 13.1 Test Loops 123
- 13.2.1 Problems 124
- 13.2.2 Initialization Errors 125
- 14 Appendix 126
- 14.2 Referenced Documents 128
Powiązane produkty i podręczniki dla Networking Schmid Watson
Networking Schmid Watson Dokumentacja
(130 strony)
(130 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 2.191 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji